機械社區
標題: 美國的斜齒輪圖紙的英文,誰能幫忙翻譯下,不勝感激! [打印本頁]
作者: yang13564 時間: 2010-9-28 10:20
標題: 美國的斜齒輪圖紙的英文,誰能幫忙翻譯下,不勝感激!
1.) G6 ]0 y/ P% s
Quality: ANSI/AGMA 2000-a88-q11, full depth, full fillet.
2.
/ Y0 b! j4 ], NFOR LEAD, CROWN, AND PROFILE TOLERANCES SEE DWG 54773379
3.
& e8 d; c3 p' W4 k" k4 lCROWN DRIVEN GWAR ONLY
4.- x9 T) K" Z1 K
NORMAL PRESSURE ANGLE 20”
5.- b9 A0 P6 D# w# a! `
NORMAL DIAMETRAL PITCH 8
6.
* _, V2 T( ~: _* e2 L GNORMAL CIRAULAR PITCH 0.3927
7., E" `& \* f8 a+ P% r7 B- {
HELIX ANGLE:16.6011
8.
+ s! i# R9 {+ g5 B5 Z! o$ aBACKLASH TO BE 0.996” TO 0.008” ON 6.9784” CENTERS
9.
/ |) ^4 s6 t# @& F7 e' D! }MATERIAL: AISI 8620
10.) ?" s# X- b/ `, K; A, c
CASE CARBURIZE TO 0.025” TO 0.040” EFFECTIVE FEPTH AFTER GRINDING AND HARDEN TO 57-61 RC, CORE HARDNESS7 g7 N& e% O: W% H; ?" F
TO BE 25-40 RC.
11.8 z* |% j7 {6 [0 q7 U
RETAINED A USTENITE – 5% MAXIMUM BY VISUAL INSPECTION.
12.3 `( t6 R2 g0 |! N
EACH GEAR DEAR SET TO BE BOXED SEPARATELY AS A SET AND EACH GEAR MARKED WITH THE SET PART NUMBER ON THE OUTSIDE. EACH GEAR TO HAVE P/N AND SUPPLIER INENTIFICATION STAMPED. EACH GEAR TO HAVE P/N AND SUPPLIER IDENTIFICATION SATAMPED OR ELECTRIC ACID ETCHED AS SHOWN, APPROX. TEXT HGT..25’.
13.
0 S9 |1 s5 u0 ~9 }1 b5 g# e' @& IREMOVE ALL CHIPS FROM TAPPED HOLES.
NUMBER OF TEETH
HAND OF HELIX
LEAD OF HELIX
PIRTCH DIAMETER
BASE CIRCLE DIAMETER
ADDENDUM
WHOLE DEPTH
TRANSVERSE CIRCULAR
TOOTH THICKNESS WO/BL
NORMAL CIRCULAR
TOOTH THICKNESS WO/BL
作者: yang13564 時間: 2010-9-30 08:14
本帖最后由 yang13564 于 2010-9-30 08:15 編輯 9 w& f' U$ D5 s7 S! \: A
2 l( c/ [ }7 v6 ~. n+ S2 m. Z. ~* o沒有人翻譯,找到了資料,不知道對不對!望高手出來指正!
. S' h) H- i; _4 G/ o+ b7 |1 e+ @ 齒輪制造標準和精度等級：ANSI/AGMA 2000-A88,，精度12級，全深,，全倒角,。4 l' |9 I& u4 `: V( A4 T: l0 v! q
齒向、齒形修緣和漸開線輪廓公差按54773379圖紙規定,。7 p z* e1 V1 a; c( F
僅驅動齒輪鼓形修整,。
9 W/ z6 q8 |$ X 齒形壓力角20º3 k6 ~7 R6 I, G8 @- t1 g1 z
節徑DP=10
. n# T. g; l4 \ 齒距：0.3142
0 f; V" s' G w! X8 i3 ]4 n0 c 螺旋角：15.9355º
2 R' u: D% J2 ]8 _ 在齒輪嚙合中心距5.5118”上,，側隙要求在0.006” ~0.010”之間,。
; l# k: Q, a8 a9 m C) U' h: U 齒輪材料：AISI 8620/ U% s Z0 w9 t% d' y0 w
滲碳層0.025”~0.040”有效深度,，表面硬度為57~61Rc,，芯部硬度25~40Rc,。) ]- r$ @5 f3 n
殘余奧氏體最大5%目測檢查,。2 t% |) Y6 K2 |# y* g6 D" I: v5 O
每個周轉盒內只能裝一個齒輪組,，周轉盒外標記齒輪組圖號,，齒輪表面須按圖示部位用電蝕法標記零件號和供貨商代碼,，字高約0.25。 d- y& N" i% r7 m7 \
攻絲后,，去除螺紋孔內的鐵屑,。
作者: qvzhiwei 時間: 2010-11-11 17:02
樓上玩意的好專業,，佩服！�,�,！
作者: another 時間: 2010-11-21 20:44
二樓挺專業的···感覺還不錯，很值得學習,。
| 歡迎光臨 機械社區 (http://97307.cn/) |
Powered by Discuz! X3.4 |