標題: 如何 把讀取的10個數據直接計算出平均值,？ [打印本頁] 作者: LpJ1988 時間: 2011-5-16 20:32 標題: 如何 把讀取的10個數據直接計算出平均值？ 我想在現有的生產線彈簧受力程序中添加一段計算平均值的程序,，原程序僅讀取一個隨機值然后輸出,。5 o" H0 }1 ]0 T! [( J& v$ g
因?yàn)閺椈墒芰τ行》鹊恼鹗�,，所以我想讓程序讀取10個值，然后算出平均值輸出,。 4 R( W, c) P) F7 {& |( v. h0 n& V& r關于提取測量數據計算平均值的程序,，小弟實在是學得太少。,。只會輸入幾個數求平均值的程序,。* w" {6 t" R& f/ g
下面這段是原程序，感謝進來幫忙的高手們�,�,！! ?2 l5 P5 e, v1 e9 \$ y7 ~
JU S_00; / / Wait for release 1 y, Q3 P7 ]$ C& Q JU S_01; / / Read controller status and decide whether to start is needed. - U- Q/ G @7 | e1 o( }
JU S_02; / / Start CanOpenNode (if necessary) then return to Step 1. / y) d u0 q' k9 G4 K$ v
JU S_03; / / Reserve Step ) x O) T1 G2 j# N0 i/ O JU S_04; / / Read current position in increments # V, T! Y5 J# M
JU S_05; / / Read current limit set in mA + K' ]2 P- Z- F JU S_06; / / Read current flow in 1 / 1000 to current limit 4 o8 {. k! e' C4 u) C2 q JU S_07; / / Read back ( f( D4 Z6 Q' | ? JU S_08; / ??/ Read back : |4 ^+ G, }5 w e1 j8 \9 h F JU S_09; / / Read back ; ]) `' _( s6 n/ S' J JU S_10; / / write the forward position 8 v$ |$ Y& E e; f9 ^. R JU S_11; / / Write back position . s6 x, d1 q6 r+ {' I
JU S_12; / / Write Maximum Test Current # I/ q6 S6 C4 p9 P% c# U( M( A
JU S_13; / / write back / W1 D, \/ c' ~/ m g* p6 A JU S_14; / / write back 6 [* Z3 v5 V6 @; Q" j. L/ y JU S_15; / / write back & }! q+ f7 F% h& w' Z; m JU S_16; / / write back 2 [% Y2 f+ m! E6 |$ n
JU S_17; / / write back , I$ V5 [; k/ H; s r; b作者: fmdd 時間: 2011-5-16 21:37
累加器) O* y% P! a4 V! ~* k
計數器 1 z% z/ ]4 x2 X! Z0 |( Q累加之后除以/計數，就是平均值
! ?2 l5 P5 e, v1 e9 \$ y7 ~