[4A] 這張齒輪圖紙的技術說明，你能看出哪里需要完善？

十年一夢

大家討論一下有什么需要完善之處。
* ]) Y% @+ f' I* _8 _: T
NOTES:
0 l* Z  v  f+ {* L0 o+ Y9 E. _1. MATERIAL: ALLOY STEEL 9310H-NORMALIZED & TEMPERED TP HRc 32-40
(AIR CRAFT QUALITY FORGING).
" u& O, R& |: j' o0 ~% E, a2. CENTERS ARE MANDATORY ON BOTH ENDS OF SHAFT. ALL DIAMETERS MUST
9 Q, S+ C. Q$ f: f, S- R# qBE MACHINED USING THESE CENTERS AND -A- & -B- DIAMETERS MUST BE
CONCENTRIC TO THESE CENTERS WITHIN 0.005 TIR.
% F4 V% F6 Z# i/ Y, _3. DYNAMICALLY BALANCE WITHING 0.26 OZ-IN AT PLANES INDICATED.
: t% ]/ |  r; E3 t5 Q: @3 BINSTALL HALF-KEY IN THE KEYWAY DURING BALANCING.
2 t+ b1 E4 p. a- }5 `4. PROTECT THESE SURFACES FROM SCRATCHES AND TOOL MARKS.
; N+ x4 F$ X0 h5. WHILE HOBBING LEAVE .29-.30 GRINDING STOCK TO FINISH THE GEAR.
9 U) u2 K' Q0 s7 D+ V6. CASE CARBURISE AREA MARKED (**) AND HARDEN TO RC 58-64. FINISHED
CASE DEPTH TO BE RC 50 AT 0.4-0.6 DEEP. REMAINDER TO BE RC 32-40.
7. GRIND THE TEETH PER GEAR DATA AFTER HARDENING.
8. DO NOT GRIND ROOT OF GEAR TOOTH. USE PROTUBERANT HOB.
, p6 d) @: t% W9. ALL FILLET RADII TO BE CAREFULLY BLENDED, POLISHED AND FREE OF
TOOL MARKS.
  C0 e. ]$ o2 D10.UNLESS OTHERWISE SPECIFIED, CONCENTRICITY, SQUARENESS &
& G/ Q' b8 d# N* B4 o# T( }7 ePARALLELISM TO BE WITHIN 0.254 TIR
11.GEAR ACCURACY DATA TO BE DETERMINED FROM DATUM -A- & -B- (SHAFT).
- T' _" R6 L$ [$ o$ q/ j12.MAGNETIC PARTICLE TEST AND INSTPECT.
13.AFTER FINAL GRINDING, BLEND ALL SHARP EDGES, REMOVE ALL BURRS.
6 n6 u# N9 K% Z8 j) D& B9 i0 R14.BURNISH MARKED AREA WITH (*).

機械神話

希望看到這張圖，機械圖紙是圖文并存的,，不可分離,。

itwotwo

這是你自己出圖紙給鬼佬加工的？
1. MATERIAL: ALLOY STEEL 9310H-NORMALIZED & TEMPERED TP HRc 32-40.(AIR CRAFT QUALITY FORGING).
0 u* B- w: ?! \8 y7 L0 n% t" K9 Y材質應寫入材質欄,，這里只要寫熱處理方式和最終硬度
" q& S: a/ b$ U$ I0 s+ F' n2. CENTERS ARE MANDATORY ON BOTH ENDS OF SHAFT. ALL DIAMETERS MUST BE MACHINED USING THESE CENTERS AND -A- & -B- DIAMETERS MUST BE CONCENTRIC TO THESE CENTERS WITHIN 0.005 TIR.
這里的軸可能用axis比較合適,，因?yàn)檫@根軸線不是實際存在的東西，同軸度本身就是個跳動值所以不用TIR,。更應該直接標在圖上,。
3.DYNAMICALLY BALANCE WITHING 0.26 OZ-IN AT PLANES INDICATED INSTALL HALF-KEY IN THE KEYWAY DURING BALANCING.
半鍵連接？動平衡因該在整根軸帶齒輪的裝配體完成后整體做的,，把這個要求寫在這里應該要REF一個裝配圖要求,。
0 f8 v: x4 j' |4. PROTECT THESE SURFACES FROM SCRATCHES AND TOOL MARKS.
1 [' {* x6 ~; M! V# r$ P保護刮傷正常,，保護刀痕不正常,。刀痕都是加工出來的，不存在保護就會消失,。
5. WHILE HOBBING LEAVE .29-.30 GRINDING STOCK TO FINISH THE GEAR.
$ @/ b& i+ X" e,？這是客戶對供應商的產品需求嗎？怎么看起來像打工做工藝分析的,？
& h# ?( l6 S5 g7 ^1 o1 T' h6. CASE CARBURISE AREA MARKED (**) AND HARDEN TO RC 58-64. FINISHED CASE DEPTH TO BE RC 50 AT 0.4-0.6 DEEP. REMAINDER TO BE RC 32-40
7. GRIND THE TEETH PER GEAR DATA AFTER HARDENING
8 r. J! b8 ?0 ^% z; I) i( y8. DO NOT GRIND ROOT OF GEAR TOOTH. USE PROTUBERANT HOB.
這是不是滾壓齒底的意思,？用roll
" r6 A8 T# {" ~) {) W# @" d/ L' T9. ALL FILLET RADII TO BE CAREFULLY BLENDED, POLISHED AND FREE OF TOOL MARKS.
倒角處訂個1.6的光潔度就行
8 s: ?9 k6 g  C, O; U  t10.UNLESS OTHERWISE SPECIFIED, CONCENTRICITY, SQUARENESS & PARALLELISM TO BE WITHIN 0.254 TIR
同軸度，垂直度,，平行度都要有參照標準的,，哪有可能沒有specified啊,？而且本身這3個值本身就是TIR,，不需要說明
7 ~3 [# H' ?! ~, E' c* }# b) l% m12.MAGNETIC PARTICLE TEST AND INSTPECT.
探傷之后要說哪些區域有傷可接受或者全部不接受
8 _8 q' e$ ~& c13.AFTER FINAL GRINDING, BLEND ALL SHARP EDGES, REMOVE ALL BURRS.
我通常會用Break all burr. Sharp edge本身在機械零件里不是缺陷，該有的地方是你設計成它有。要是日用品就不能存在sharp edge,。
14.BURNISH MARKED AREA WITH (*).

- O, W+ u/ ]$ n9 g1 c4 j8 q. p: \老兄的東西每次看都有新發現,。但是如果是一個齒輪的note，好像該有的東西全部沒有：
top circle
( |0 z' Q' E3 S* u! _root circle
addendum
" Y/ Z8 n1 t$ y6 Mdedendum
; Z: M7 z5 \% q1 F) atooth height
6 u5 _: M, o+ y6 D& V; hpitch distance
這些都應該有上下公差或者標準值
/ ]& W: Z5 T  w1 Zpresure angle應該要指出
- S- `! a/ K! ]: Y

qdtruck

沒有圖紙?jiān)趺捶治霭,�,？樓上有圖紙了？

supperslz

無圖無真相另,，另外還要說一下功用,。

271211310

你需要的是真正的高手

宇宙立方

愛顯擺也是人類原罪之一

湘中人

無圖無真相！,！

云飄映月

高手啊,，三樓

混日子

樓主你這應該是單個零件的技術要求吧？我覺得第三條動平衡應該去掉,，單個零件的在這沒什么用,；第五條磨削余量沒必要寫在這個里面吧，畢竟是工藝要求,；另外,，你要求表面刀紋看不出，那就直接定個粗糙度Ra1.6以下,，這個可去參考粗糙度標準樣塊,；第十條未注同心度0.254你有和第三條校核沒？單位是英制還是公制,？有必要到小數點后三位,？還有最后那條不太清楚你要干什么。