[4A] 這張齒輪圖紙的技術說明,，你能看出哪里需要完善,？

十年一夢

大家討論一下有什么需要完善之處,。

0 N8 ^: _, ]5 d2 sNOTES:
1. MATERIAL: ALLOY STEEL 9310H-NORMALIZED & TEMPERED TP HRc 32-40
5 z) W& E$ f& x0 D$ v9 L(AIR CRAFT QUALITY FORGING).
4 v; t* J* J/ C2. CENTERS ARE MANDATORY ON BOTH ENDS OF SHAFT. ALL DIAMETERS MUST
. h7 ]( X6 n/ D% k# v" T3 q% r6 _$ \BE MACHINED USING THESE CENTERS AND -A- & -B- DIAMETERS MUST BE
' y  p" }, j7 h. X3 ], KCONCENTRIC TO THESE CENTERS WITHIN 0.005 TIR.
3. DYNAMICALLY BALANCE WITHING 0.26 OZ-IN AT PLANES INDICATED.
1 y' H1 D8 w& v8 {# S1 {! a& L/ C  R7 JINSTALL HALF-KEY IN THE KEYWAY DURING BALANCING.
4. PROTECT THESE SURFACES FROM SCRATCHES AND TOOL MARKS.
: [: J4 x- R4 l) [% d* [5. WHILE HOBBING LEAVE .29-.30 GRINDING STOCK TO FINISH THE GEAR.
6. CASE CARBURISE AREA MARKED (**) AND HARDEN TO RC 58-64. FINISHED
$ u  }+ K4 v5 j: CCASE DEPTH TO BE RC 50 AT 0.4-0.6 DEEP. REMAINDER TO BE RC 32-40.
3 f; }6 G4 ?$ P. _) n7. GRIND THE TEETH PER GEAR DATA AFTER HARDENING.
  ]% k, P& Z) }  U  l8. DO NOT GRIND ROOT OF GEAR TOOTH. USE PROTUBERANT HOB.
- V3 u* S! t9 Z3 h1 S# @* r9. ALL FILLET RADII TO BE CAREFULLY BLENDED, POLISHED AND FREE OF
1 w5 J) l: {7 bTOOL MARKS.
" }3 {: `/ q  ]' t) ?! s3 S10.UNLESS OTHERWISE SPECIFIED, CONCENTRICITY, SQUARENESS &
PARALLELISM TO BE WITHIN 0.254 TIR
11.GEAR ACCURACY DATA TO BE DETERMINED FROM DATUM -A- & -B- (SHAFT).
12.MAGNETIC PARTICLE TEST AND INSTPECT.
13.AFTER FINAL GRINDING, BLEND ALL SHARP EDGES, REMOVE ALL BURRS.
14.BURNISH MARKED AREA WITH (*).
+ F& h  I# ?( C  ?& `  u. O

機械神話

希望看到這張圖,，機械圖紙是圖文并存的，不可分離,。

itwotwo

這是你自己出圖紙給鬼佬加工的,？
1. MATERIAL: ALLOY STEEL 9310H-NORMALIZED & TEMPERED TP HRc 32-40.(AIR CRAFT QUALITY FORGING).
) L% f2 S4 g7 c1 U- ~( ]+ N材質應寫入材質欄，這里只要寫熱處理方式和最終硬度
2. CENTERS ARE MANDATORY ON BOTH ENDS OF SHAFT. ALL DIAMETERS MUST BE MACHINED USING THESE CENTERS AND -A- & -B- DIAMETERS MUST BE CONCENTRIC TO THESE CENTERS WITHIN 0.005 TIR.
5 C$ M- @4 U1 {- X" t這里的軸可能用axis比較合適,，因為這根軸線不是實際存在的東西,，同軸度本身就是個跳動值所以不用TIR。更應該直接標在圖上,。
; c4 a! f( u8 w( N- b3.DYNAMICALLY BALANCE WITHING 0.26 OZ-IN AT PLANES INDICATED INSTALL HALF-KEY IN THE KEYWAY DURING BALANCING.
# X; @2 D% D$ F* B4 P% F7 X3 d半鍵連接,？動平衡因該在整根軸帶齒輪的裝配體完成后整體做的，把這個要求寫在這里應該要REF一個裝配圖要求,。
4. PROTECT THESE SURFACES FROM SCRATCHES AND TOOL MARKS.
保護刮傷正常,，保護刀痕不正常。刀痕都是加工出來的,，不存在保護就會消失,。
; K+ `* j  F0 k5. WHILE HOBBING LEAVE .29-.30 GRINDING STOCK TO FINISH THE GEAR.
$ ^) C0 l0 f# m# E& l？這是客戶對供應商的產品需求嗎,？怎么看起來像打工做工藝分析的,？
& r( r7 Z3 l$ W! d6. CASE CARBURISE AREA MARKED (**) AND HARDEN TO RC 58-64. FINISHED CASE DEPTH TO BE RC 50 AT 0.4-0.6 DEEP. REMAINDER TO BE RC 32-40
7. GRIND THE TEETH PER GEAR DATA AFTER HARDENING
8. DO NOT GRIND ROOT OF GEAR TOOTH. USE PROTUBERANT HOB.
, `/ c1 x2 y/ b& X# j1 S這是不是滾壓齒底的意思？用roll
9. ALL FILLET RADII TO BE CAREFULLY BLENDED, POLISHED AND FREE OF TOOL MARKS.
6 f& M: t# Q& _9 a2 ^; b倒角處訂個1.6的光潔度就行
10.UNLESS OTHERWISE SPECIFIED, CONCENTRICITY, SQUARENESS & PARALLELISM TO BE WITHIN 0.254 TIR
6 q1 f! I6 O% \. H同軸度,，垂直度,，平行度都要有參照標準的，哪有可能沒有specified�,�,？而且本身這3個值本身就是TIR，不需要說明
4 G- |( Z! A: o- f12.MAGNETIC PARTICLE TEST AND INSTPECT.
- c% l  a( q+ T; `7 }探傷之后要說哪些區域有傷可接受或者全部不接受
13.AFTER FINAL GRINDING, BLEND ALL SHARP EDGES, REMOVE ALL BURRS.
我通常會用Break all burr. Sharp edge本身在機械零件里不是缺陷,，該有的地方是你設計成它有,。要是日用品就不能存在sharp edge。
  ^6 f6 ^5 @8 V6 o9 |14.BURNISH MARKED AREA WITH (*).

老兄的東西每次看都有新發現,。但是如果是一個齒輪的note,，好像該有的東西全部沒有：
top circle
root circle
/ b9 {; l( K8 `9 T) x( A0 [, taddendum
  P! z9 O, J4 [* |3 t3 s* rdedendum
; m7 f( T6 z+ b$ n. R' t( Ytooth height
pitch distance
這些都應該有上下公差或者標準值
presure angle應該要指出
5 L  i, C4 W7 L
  [, q( _/ l, l. J" \+ n

qdtruck

沒有圖紙怎么分析�,。繕巧嫌袌D紙了,？

supperslz

無圖無真相另,，另外還要說一下功用。

271211310

你需要的是真正的高手

宇宙立方

愛顯擺也是人類原罪之一

湘中人

無圖無真相�,�,！

云飄映月

高手啊，三樓

混日子

樓主你這應該是單個零件的技術要求吧,？我覺得第三條動平衡應該去掉,，單個零件的在這沒什么用；第五條磨削余量沒必要寫在這個里面吧,，畢竟是工藝要求,；另外，你要求表面刀紋看不出,，那就直接定個粗糙度Ra1.6以下,，這個可去參考粗糙度標準樣塊；第十條未注同心度0.254你有和第三條校核沒,？單位是英制還是公制,？有必要到小數點后三位？還有最后那條不太清楚你要干什么,。