[4A] 這張齒輪圖紙的技術說明,，你能看出哪里需要完善,？

十年一夢

大家討論一下有什么需要完善之處。

NOTES:
' @& D7 @- m6 E) |1 r* Y* O( K1. MATERIAL: ALLOY STEEL 9310H-NORMALIZED & TEMPERED TP HRc 32-40
4 I/ |3 \8 o( Q(AIR CRAFT QUALITY FORGING).
2. CENTERS ARE MANDATORY ON BOTH ENDS OF SHAFT. ALL DIAMETERS MUST
+ k( h1 X. b' M$ m, nBE MACHINED USING THESE CENTERS AND -A- & -B- DIAMETERS MUST BE
8 x. \4 `. x$ ^: c$ B& ACONCENTRIC TO THESE CENTERS WITHIN 0.005 TIR.
- Y/ J" v) ^5 b* G: V$ L3. DYNAMICALLY BALANCE WITHING 0.26 OZ-IN AT PLANES INDICATED.
INSTALL HALF-KEY IN THE KEYWAY DURING BALANCING.
4. PROTECT THESE SURFACES FROM SCRATCHES AND TOOL MARKS.
5. WHILE HOBBING LEAVE .29-.30 GRINDING STOCK TO FINISH THE GEAR.
, G( h8 x2 z5 M& [- ?) B5 {6. CASE CARBURISE AREA MARKED (**) AND HARDEN TO RC 58-64. FINISHED
  S9 D5 d. u4 x3 m/ P. W  Z3 v0 FCASE DEPTH TO BE RC 50 AT 0.4-0.6 DEEP. REMAINDER TO BE RC 32-40.
7. GRIND THE TEETH PER GEAR DATA AFTER HARDENING.
0 y$ W4 Z- a) b9 C: q) {8. DO NOT GRIND ROOT OF GEAR TOOTH. USE PROTUBERANT HOB.
( `# n; z" ^3 M$ p$ ?9. ALL FILLET RADII TO BE CAREFULLY BLENDED, POLISHED AND FREE OF
TOOL MARKS.
10.UNLESS OTHERWISE SPECIFIED, CONCENTRICITY, SQUARENESS &
PARALLELISM TO BE WITHIN 0.254 TIR
, o6 d+ p2 n3 a0 _11.GEAR ACCURACY DATA TO BE DETERMINED FROM DATUM -A- & -B- (SHAFT).
12.MAGNETIC PARTICLE TEST AND INSTPECT.
. F4 D" `# N1 C$ q, T  z3 {) `% e13.AFTER FINAL GRINDING, BLEND ALL SHARP EDGES, REMOVE ALL BURRS.
1 E* I0 G. b* q9 }- r  _, B14.BURNISH MARKED AREA WITH (*).
2 }! d* L: `; u" d

機械神話

希望看到這張圖，機械圖紙是圖文并存的,，不可分離,。

itwotwo

這是你自己出圖紙給鬼佬加工的？
, E7 `6 l' \& D1 p) \" v1. MATERIAL: ALLOY STEEL 9310H-NORMALIZED & TEMPERED TP HRc 32-40.(AIR CRAFT QUALITY FORGING).
4 x, D1 C+ e; l! h4 ]材質應寫入材質欄,，這里只要寫熱處理方式和最終硬度
2. CENTERS ARE MANDATORY ON BOTH ENDS OF SHAFT. ALL DIAMETERS MUST BE MACHINED USING THESE CENTERS AND -A- & -B- DIAMETERS MUST BE CONCENTRIC TO THESE CENTERS WITHIN 0.005 TIR.
( j1 |5 m5 M# y: W# g( m9 s這里的軸可能用axis比較合適,，因?yàn)檫@根軸線不是實際存在的東西，同軸度本身就是個跳動值所以不用TIR,。更應該直接標在圖上,。
5 k* T; H- A) S2 \0 l/ `) E3 C3.DYNAMICALLY BALANCE WITHING 0.26 OZ-IN AT PLANES INDICATED INSTALL HALF-KEY IN THE KEYWAY DURING BALANCING.
半鍵連接？動平衡因該在整根軸帶齒輪的裝配體完成后整體做的,，把這個要求寫在這里應該要REF一個裝配圖要求,。
6 B1 f+ Q1 q. k4. PROTECT THESE SURFACES FROM SCRATCHES AND TOOL MARKS.
保護刮傷正常，保護刀痕不正常,。刀痕都是加工出來的,，不存在保護就會消失。
5. WHILE HOBBING LEAVE .29-.30 GRINDING STOCK TO FINISH THE GEAR.
,？這是客戶對供應商的產品需求嗎,？怎么看起來像打工做工藝分析的？
6. CASE CARBURISE AREA MARKED (**) AND HARDEN TO RC 58-64. FINISHED CASE DEPTH TO BE RC 50 AT 0.4-0.6 DEEP. REMAINDER TO BE RC 32-40
. i, T: e" z5 W; Q/ }7. GRIND THE TEETH PER GEAR DATA AFTER HARDENING
8. DO NOT GRIND ROOT OF GEAR TOOTH. USE PROTUBERANT HOB.
這是不是滾壓齒底的意思,？用roll
% x7 O% _* M' a9. ALL FILLET RADII TO BE CAREFULLY BLENDED, POLISHED AND FREE OF TOOL MARKS.
' b! g% H% k" t+ y3 q! \1 K倒角處訂個1.6的光潔度就行
8 c/ `! s7 d8 u! p3 K0 I" }10.UNLESS OTHERWISE SPECIFIED, CONCENTRICITY, SQUARENESS & PARALLELISM TO BE WITHIN 0.254 TIR
. D2 j( [5 m4 [+ M同軸度,，垂直度，平行度都要有參照標準的,，哪有可能沒有specified�,。慷�且本身這3個值本身就是TIR,，不需要說明
12.MAGNETIC PARTICLE TEST AND INSTPECT.
- s0 @4 q% d' X4 {探傷之后要說哪些區域有傷可接受或者全部不接受
13.AFTER FINAL GRINDING, BLEND ALL SHARP EDGES, REMOVE ALL BURRS.
我通常會用Break all burr. Sharp edge本身在機械零件里不是缺陷,，該有的地方是你設計成它有。要是日用品就不能存在sharp edge,。
( ^0 Y% K; Z: }, V, ~9 z14.BURNISH MARKED AREA WITH (*).
+ h6 t1 O; i: W2 \: M" |1 s
老兄的東西每次看都有新發現,。但是如果是一個齒輪的note，好像該有的東西全部沒有：
top circle
root circle
addendum
dedendum
tooth height
& o# R& [, d# }  g3 N3 X! Y1 B- Opitch distance
這些都應該有上下公差或者標準值
+ G: o7 P' t+ |" W4 z+ ^; D! ?presure angle應該要指出

qdtruck

沒有圖紙?jiān)趺捶治霭,�,？樓上有圖紙了？

supperslz

無圖無真相另,，另外還要說一下功用,。

271211310

你需要的是真正的高手

宇宙立方

愛顯擺也是人類原罪之一

湘中人

無圖無真相！,！

云飄映月

高手啊,，三樓

混日子

樓主你這應該是單個零件的技術要求吧？我覺得第三條動平衡應該去掉,，單個零件的在這沒什么用,；第五條磨削余量沒必要寫在這個里面吧，畢竟是工藝要求,；另外,，你要求表面刀紋看不出，那就直接定個粗糙度Ra1.6以下,，這個可去參考粗糙度標準樣塊,；第十條未注同心度0.254你有和第三條校核沒？單位是英制還是公制,？有必要到小數點后三位,？還有最后那條不太清楚你要干什么。