那位大俠幫我翻譯成英語？非常感謝,！

一顆豆芽

1,、打槽工裝調整不到位
1.1、各底座安裝不同軸
7 X# \9 x: P1 y: O; O9 ^1.2,、零件安裝的松緊程度不適合
$ a- o0 f1 w- C6 @1.3,、壓桿安裝的松緊程度不適合
1.4、打槽機空間小調整困難
4 \: C! W7 F$ R2 }5 a" b2,、加工前沒有檢查沖針的磨損程度
2 X" H  W9 B0 {3、打槽機工裝不適合M15/M16產品加工
3.1,、底座不能安裝高度為2.9mm的產品
' K$ q& Z) B9 l1 z+ \9 D2 q! J3.2、壓桿不能固定OD＜75的產品
* w8 T9 R" Y1 e, X8 x3.3,、壓塊不能壓緊產品
4、沖針切削阻力大,，尺寸變化大
+ e) F8 x3 Z6 y0 S6 n4.1沖針形狀不適合
6 F+ z6 a* J. P0 f5、氣缸不穩定
5.1,、氣壓不穩定
( o, |# }* n  G( S+ `/ L5.2、沖針?biāo)蓜?/font>
5.3,、氣缸松動
6,、產品外徑小，剖面小裝夾困難
  ~5 v: h- g6 w0 |/ b7,、產品易塑性變形,，加工困難
! e2 _4 A* R& I* }' h2 J8、槽尺寸測量困難


  G. N5 _$ b  e9 ^兄弟的英語實在是太難了,。上面這些需要給老板看,，那位好心的幫幫忙啊,！

唯獨懂你

In 1, playing the slot tooling adjustment does not reach the designated positionIn
& H. d, j* S# P/ { 1.1, the base mounting shaft
1.2, the degree of tightness for mounting parts
1.3, the degree of tightness of the pressure rod is arranged forIn
1.4, playing the slot machine in the whole space is difficultIn
2, prior to processing did not check the degree of wear of the punch needleIn
3, playing the slot machine tooling is not suitable for M15\/M16 products processingIn
; Y, Y9 ?- r. G. E/ k2 q/ b3.1, the base can not be installed height of 2.9mm products
3.2, push rod can not be fixed OD < 75 productsIn
- D9 k+ I9 _2 S$ q4 n1 _3.3, the pressing block can not be pressed productsIn
4, the punching needle big cutting resistance, dimensional change
4.1 punch needle shape is not suitable forIn
5, the cylinder is not stableIn
5.1, the pressure of not stableIn
1 Q' z& L: Y/ ]" w2 L/ S% W5.2, the punching needle looseningIn
2 p) M: I$ W0 t" W  ^: _3 ?5.3, the cylinder is looseIn
6, the product of small external diameter, small difficult clamping sectionIn
7, the product easy to plastic deformation, difficult processing
8, groove size measurement difficulties以后自己在百度上面可以翻譯，中英文翻譯就行,。

baikenor

谷歌翻譯  感覺不錯    翻譯之后再翻回去可以驗證有沒有不準確的地方

一顆豆芽

非常感謝各位